About Us

Welcome!

Hi there! We are the Curren Family. We traveled full time in our Airstream from 2013-2017 and now split our time between our small condo in Teton Valley, ID and the road.

As avid, outdoor, travel and adventure enthusiasts we are here to provide tips, advice, and inspiration to help you develop healthier and stronger family relationships.

Follow Us

Email Subscribe

Airstream Gear: Getting Cranky

Our Airstream has 4 stabilizers that we used when parked to keep it from moving around. Many folks use a power drill and bit to run these up and down, but I prefer to assign that job to my kids, who don’t have enough chores anyway.

This leads us to the crank: stored in our bumper compartment, the crank is what we use each time we move. When we bought the Airstream, the previous owner included a swivel-head crank. Within a few months, the pin connecting the socket to the crank handle broke, and I replaced it.

IMG_20140910_191000

As full time travelers, we use our travel gear much more often than normal weekend folks. Tools used a few times a year by a normal traveler get used 50 to 100 times by a full-time traveler. Within a few months, the pin broke on the new crank, and I started getting cranky.

Finding a replacement pin turned out to be an exercise in frustration, as the pin was a custom part that was completely un-findable. I rigged a temporary pin by bending an extra allen wrench into place and holding it in place with some tape.

I ended up replacing the pin with a screw and nut I bought at the hardware store. I bought a 10 pack of each, and simply replaced the pin every 4 to 6 weeks when it broke. That was 10 months ago, and I just used my last screw and bolt.

I’m tired of the constant repair. The crank is otherwise in good shape, but if the stupid pin won’t hold up, it isn’t much use to me. I’ve decided to replace my crank with a non-swivel model, in the hope that fewer moving parts will also require less repair and replacement. The new crank provides less leverage then the old one, but I’ll be happy to deal with that if it remains in working condition longer than a few weeks.

Early reports from the kids (the primary crankers in this operation) indicate probable success. We’ll see how they do long term!

2 comments
Add a comment...

Your email is never published or shared. Required fields are marked *

  • Sam,

    I know what you’re looking for, and I have the solution sitting in my toolkit…

    1) A 3/4″ 6 point socket, like the one in this kit. http://goo.gl/oJnA8h

    2) A bent flex-head ratchet. http://goo.gl/KhOIkO This will allow you to put the handle parallel to the stabilizer jack screw and “crank” it quickly with both hands like the current handle when there’s no resistance, then flex the head to be perpendicular to the stabilizer jack screw and use it like a regular ratchet for the last little bit where you need a little oomph. (It’ll totally make sense once you’ve got one in your hands, I promise!)

    3) A ‘wobble’ extension of a length to suit your preference.

    In use, you fit the 3/4″ socket on the end of the wobble extension, and that gives you about 20* of ‘play’ for the extension, then the flexhead ratchet is bent, so that you can crank it quickly down, then unflex the head and crank the stabilizer jack down taut.

    I don’t remember where I got my bent/flex ratchet, but it’s the tool that I use more than anything else on pretty much every project.
    The wobble extension + flex head ratchet set lets me get a socket (or allen key or screwdriver bit) into places that would otherwise be completely obstructed by other ‘bits’…

    Highly recommended.ReplyCancel

  • You shouldn’t find too many issues with your setup, at least it shouldn’t break!

    We use a combination of the crank and power drill. With the power drill my wife can go around and crank the ‘corners’ down quickly. I follow behind and give each one about 1/4 to 1/2 turn to tighten them down. We do the reverse to take them up.

    However you are much younger and do have access to some extra assistance…ReplyCancel

Partners & Affiliates

We've tried and tested many companies and only bring you the best! By clicking on our links we receive a small kickback and it doesn't cost you anything. Thanks so much for your support!

©2019 Peak Ventures LLC. All rights reserved. Republication in part or entirety requires a link back to the original post AND permission from the author. 

Occasionally we will partner with a company or brand and/or provide affiliate links on our site. All opinions are always our own and generally we've vetted things pretty well before presenting them to our readers. 

We are not professionals and although we provide trip reports or adventure ideas please research and do your own due diligence before embarking on any trip.