About Us

Welcome!

Hi there! We are the Curren Family. We traveled full time in our Airstream from 2013-2017 and now split our time between our small condo in Teton Valley, ID and the road.

As avid, outdoor, travel and adventure enthusiasts we are here to provide tips, advice, and inspiration to help you develop healthier and stronger family relationships.

Follow Us

Email Subscribe

Queen to Twins Remodel-Part III

In Part 1 of this post, we removed most of the queen, , and cut the bottoms and the tops of the beds to fit the space we needed.

Part 2 involved Sam working with his dad to build the bed frames, trimmed them with beautiful dark wenge, cut and hinged the top pieces for each bed, and relocated the heater vent.

IMG_20140506_201602

After finishing the trim and installing and hinging the tops to all 3 beds, there was just a “little” work left to be done.

Installed Gas Springs:

Our queen bed was held in the up position with some gas springs to make the area underneath more accessible. We knew we wanted these for the new beds, and I ended up ordering these from Amazon after some measuring (and guessing!) about which ones I needed. The important measurements include the open length, the closed length, and the pounds of force when open. The ‘weakest’ springs I could commonly find (24lbs) were plenty for my needs, and I just did some approximation for the length. During installation, I carefully measured my mounting points to make sure the springs would allow the beds to lower properly. I had to order the brackets (the silver things) separately, which allowed me to buy the type of bracket I wanted.

Queen to Twin Part III_08

 

Bookshelves:

My design for the beds left rounded quarter circle space at the corner of the beds where the nightstands used to be. I wanted to cover that space with some bookshelves for the kids. The bookshelves will cover small storage spaces as well.

Cutting curved boards to cover the space can be tricky. First, I cut a scrap board that was too small for the space. Then, I used a compass to scribe a line on the scrap a constant distance from the curved edge of the wall.

IMG_20140507_162024

I then use the same compass, set to the same distance, to scribe a line offset onto the final board. I cut on that scribed line.

IMG_20140507_172518The fit was still (intentionally) a bit large, and I used a pencil against the side of the Airstream to cut down the fit. Notice that hole in the aluminum? It’s a screw hole from the old nightstand. More on that in a minute.

IMG_20140507_174104

Finishing Up the Trim:

When I removed the queen, I left the back side of the box under the bed. This allowd me to leave all the electrical wiring in place under the bed. the trouble was, the plywood was faced with white melamine, which was a bit ugly to see at the end of our now longer hallway. We solved the problem with two plywood panels taken from the no-longer used nightstands. It required two pieces, aligned with unglued wood biscuits and screwed through the back of the white faced melamine plywood. In the picture below, you can see both the white melamine, and the joint between the two re-used panels. From the front, it is very difficult to see the joint between the two.

Queen to Twin Remodel Part III_11

To save some weight, I used a jigsaw to remove the now-unneeded weight of the original plywood panels.

Queen to Twin Remodel Part III_12

The finishing touch of the whole process is the Wenge trim we used on the bottom edges and vertical supports of the bed frames. Below on the left, you can see the trim against the re-used plywood. If you look VERY close, you can see that we made a mistake on the notch cut for the trim, and cut a special piece to fit in it’s place. We hid the edge of the patch with some wax-based nail hole filler, and it’s nearly impossible to see, even when I point it out. The bottom and front trim of these beds puts a finishing touch on the projct well worth the price of the Wenge hardwood we purchased and milled for the purpose.

IMG_20140507_205435

 

Fixing Rivet Holes:

Remember those rivit holes from the old nightstands? I thought about many options to fix those holes, and finally realized there was a very simple solution. I purchased some pop rivits and a rivit gun, and simply placed a rivit in the hole. On the interior of the Airstream, there are commonly rivits in places you wouldn’t expect as part of it’s hand-made construction, and it’s the perfect camoflauge. It’s worth noting that not all rivet guns are made equal. The one picture below has a swiveling head, making it much easier to place rivets on inside curves.

IMG_20140508_205011

 

Custom Cushion:

We wanted to to make all the beds as close to “normal” as possible to prevent needing custom sheets, so we ended up with a gap between the edge of Cara’s bed and the front of the Airstream. We figured hers would be the most used as a daybed, so we called up a local custom upholstery company to come out, measure, and create a cushion for the end. Shown below is the gap we needed to fill, with the custom bookshelves on both sides.

Queen to Twin Remodel Part III_09

To see the cushion in place, tune in next time for the BIG REVEAL!

1 comment
Add a comment...

Your email is never published or shared. Required fields are marked *

Partners & Affiliates

We've tried and tested many companies and only bring you the best! By clicking on our links we receive a small kickback and it doesn't cost you anything. Thanks so much for your support!

©2019 Peak Ventures LLC. All rights reserved. Republication in part or entirety requires a link back to the original post AND permission from the author. 

Occasionally we will partner with a company or brand and/or provide affiliate links on our site. All opinions are always our own and generally we've vetted things pretty well before presenting them to our readers. 

We are not professionals and although we provide trip reports or adventure ideas please research and do your own due diligence before embarking on any trip.